New windows and doors improve comfort, cut energy bills and add long-term value to your home. Juniper Windows Fort Worth pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
Therma-Tru Impact Garage Doors: The Fort Worth Owner’s Guide
We stock and install Therma-Tru-compatible impact garage doors throughout Fort Worth, with most complete door replacements running $2,800 to $6,400 installed depending on size, wind rating, and trim package. Most owners call us the morning after a spring storm shoved debris into the door face, or when the bottom seal finally gave out and left a line of dust across the garage floor. The door still opens, but it looks rough, seals poorly, and you’re starting to wonder whether it would hold up if a real storm rolled through Tarrant County again.
Which Therma-Tru Models This Applies To
Therma-Tru doesn’t badge their impact garage doors as a single line. They build them under the Therma-Tru name as part of their broader exterior door program, and the impact-rated versions almost always carry a Miami-Dade or TDI windstorm label on the interior door skin or the hinge-side jamb. Before we order anything, we check that label, measure the door slab thickness (standard is 1-3/8″ for most Therma-Tru impact doors, with some Fort Worth builds spec’d at 1-3/4″ for higher wind exposure), and confirm the track radius. The gotcha we see most often: a homeowner orders a replacement panel or door online, matches color and style, then finds the hinge spacing is off by half an inch because their original was a commercial-series retrofit. We pull the original Therma-Tru part number whenever possible, and if the label’s gone, we measure hinge pitch and panel profile before recommending an OEM replacement or a quality aftermarket equivalent. For most Fort Worth homes, OEM Therma-Tru panels and hardware are worth the premium because the hinge templates and weatherstripping channels line up without field modification.
Signs Your Therma-Tru Impact Garage Doors Is Failing
- Storm damage that broke the skin but not the frame. Impact-rated doors take a hit and stay in place, but the outer steel or composite skin can dent, crack, or delaminate. That damage weakens the next hit and shortens door life fast.
- Bottom seal pulling away or flattening out. Fort Worth heat cycles bake rubber seals into a hard, flat strip. Water, dust, and every ant in the neighborhood find the gap. The seal is cheap; the water damage behind it isn’t.
- Panel-to-panel gaps growing. Hinges stretch under repeated opening and closing, especially on heavier impact doors. When panels start to separate, the door begins racking side to side, and the opener motor works harder to compensate.
- Hinge or roller failures at the bottom two sections. The bottom carries the most weight, so those rollers and hinges fail first. If you hear grinding or see the door jerking at one point in the cycle, stop using it and call us before the track gets chewed up.
- Snapped or stretched torsion springs. On higher-cycle Therma-Tru doors with heavier impact panels, springs fatigue. A snapped spring sounds like a gunshot in the garage and leaves the door dead weight on the opener.
Replacement Cost & What’s Included
In Fort Worth, a full Therma-Tru-compatible impact garage door replacement runs $2,800 to $6,400 installed. At the lower end, you’re looking at a single-car door, standard wind rating, basic steel or composite panels, and existing track reuse where code allows. At the upper end, it’s a double-wide, higher wind rating, upgraded insulation, and new track, springs, and hardware. Partial repairs land lower: a bottom seal replacement is typically $85 to $160, roller and hinge replacement $180 to $350, and a single panel replacement $400 to $900 depending on size and finish match. Every quote is a written, line-item price before any work starts, and our workmanship warranty runs a full year, parts and labor, in writing. That’s the 365-Day Done Right Promise, and it applies to every garage door swap we do.
DIY or Call Us?
You can safely inspect the bottom seal and panel faces yourself, and tightening loose hinge bolts is fine if you know which bolts take the load. What you should not touch on an impact-rated Therma-Tru door is the torsion spring assembly. Those springs are wound under enough tension to break a hand or worse if they let go, and impact doors run heavier springs than standard doors because the panels weigh more. We stock common Therma-Tru-compatible springs, rollers, hinges, and seals on our trucks, so most Fort Worth calls are fixed in a single visit. Sean Mackey and our crew have swapped hundreds of heavy doors across Tarrant County, and the honest truth is this: most of the failures we see are on doors someone tried to adjust themselves first. Get the numbers right up front, and the install takes care of itself. Call (682) 354-9300 and we’ll walk you through what’s worth fixing and what’s worth replacing.
FAQs
A properly installed Therma-Tru impact garage door in Fort Worth typically lasts 15 to 20 years, though the bottom seal, rollers, and springs wear out long before the panels do. Texas sun and heat cycles are the main culprit, followed by storm impact and dust intrusion into the track hardware. Plan on seal replacement every 3 to 5 years and spring replacement around the 7 to 10 year mark on a heavily used door. Call (682) 354-9300 if yours is hitting those milestones and you want exact pricing before committing.
Small dents and cosmetic scratches can sometimes be worked out, but cracked, delaminated, or punctured impact panels should be replaced rather than repaired. The impact rating depends on the structural integrity of the panel face, and bondo or patchwork won’t restore the windborne-debris resistance the door was built for. Give us a call at (682) 354-9300 and we’ll tell you honestly whether a repair makes sense on your specific door.
Most single-door Therma-Tru impact garage door replacements in Fort Worth take four to six hours from arrival to cleanup, including removing the old door, mounting new track and panels, tensioning the springs, and testing the full cycle with the opener. Double-door replacements or jobs requiring new framing can run into a second day, and we’ll tell you which before we touch a screw. Call (682) 354-9300 for a written timeline and price.
We stock the most common Therma-Tru-compatible impact door parts on our trucks: bottom seals, rollers, hinges, track brackets, and several spring sizes, so most Fort Worth repairs happen same-visit. Specialty parts like whole panels or custom wind-rated doors are ordered direct and typically arrive within 7 to 10 business days. We also carry related hardware for PGT, CGI, and CWS products if your garage happens to have a mixed setup. Call (682) 354-9300 and we’ll check the truck while you’re on the phone.
Juniper Windows Fort Worth is an independent service provider and is not affiliated with Therma-Tru. We’re the windows-and-doors specialist inside the Relay Home Co. family, founded in 2001, and every job gets a written price before work begins, a live arrival time, before-and-after photos, and a digital invoice you can pay from your phone. Call (682) 354-9300 for a free estimate on your Therma-Tru impact garage door repair or replacement.
Written by Sean Mackey, Owner, Juniper Windows Fort Worth at Juniper Windows Fort Worth, serving Fort Worth and nearby areas.
Six Reasons Homeowners Choose Juniper Windows Fort Worth
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.