New windows and doors improve comfort, cut energy bills and add long-term value to your home. Juniper Windows Fort Worth pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
- More impact certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe value pick$$
- Vinyl systems built to strict wind codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Factory-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
PGT Door Installation: The Fort Worth Owner’s Guide
PGT door installation in Fort Worth typically runs $450 to $1,400 installed, depending on whether we’re swapping a single hinge, replacing a roller assembly, or installing a full door slab and frame. We keep PGT-compatible hardware and components on our trucks, so most single-part replacements happen same-visit after the initial diagnostic. Here’s the situation we usually walk into: a Fort Worth homeowner notices the door dragging, sticking, letting daylight through a corner, or simply refusing to lock cleanly, and what starts as a minor annoyance turns out to be a worn component that’s been grinding away for months.
Which PGT Models This Applies To
Our Fort Worth PGT door installation work spans the full residential lineup, including the WinGuard and Premier Vinyl series, the ClassicVue sliding glass doors, and PGT’s hurricane-rated hinged door systems. PGT doors are built in Florida for windborne debris zones, which means the frame profiles, hinge mortises, and roller channels are machined to tighter tolerances than a lot of what we see on older Texas homes. That’s the first compatibility gotcha: big-box replacement hardware rarely fits PGT door frames without modification, so the OEM-versus-aftermarket decision matters. We’ll always quote you the real PGT-spec part first. If a quality aftermarket equivalent is available that saves $100 or more without changing the door’s operation, we’ll show you both prices and let you decide. To identify your door, look for the PGT label on the door edge or top rail, then measure the slab height, width, and the distance between hinge screws.
Signs Your PGT Door Installation Is Failing
- Door drags across the threshold on hot afternoons. Fort Worth’s summer heat cycles cause PGT’s vinyl and composite frames to expand, and once the slab contacts the threshold, the bottom sweep tears within weeks. You’ll hear it first, then see daylight under the door.
- Handle feels loose but the lock still turns. PGT multi-point lock systems use a gear-driven top and bottom shoot bolt. When the gear strips, the handle spins freely but no longer throws the top deadbolt, leaving the door held by the center latch only.
- Roller wheels grind and the panel jerks side to side. On PGT sliders, the tandem stainless rollers wear oval over five to seven years of Fort Worth dust and grit. The panel gets heavy, then it starts chewing the bottom track.
- Hinge-side screws spin without tightening. The wood buck behind the frame has rotted or the original screws were too short. Either way, the door sags, the reveal grows at the top, and the weatherstripping stops sealing.
- You can see light through the closed door corner or feel a draft at the jamb. Compression gaskets on PGT doors flatten with age, and once they lose rebound, Fort Worth winters push cold air straight through. It’s a $40 part and a 20-minute fix, but ignored long enough, the frame shifts.
Replacement Cost & What’s Included
For Fort Worth PGT door work, here’s where the money goes:
- Hinge set replacement: $450 to $650 installed, including PGT-spec hinges, shimming, and a realignment pass.
- Roller assembly replacement (sliding doors): $350 to $550 installed, including track cleaning and panel adjustment.
- Multi-point lock gearbox and handle set: $500 to $800 installed, depending on finish and whether we’re rebuilding the lock body or replacing it whole.
- Weatherstripping and threshold rebuild: $280 to $450 installed, including the new threshold cap and compression gasket.
- Full door slab and frame installation: $1,200 to $1,400 installed for a standard PGT hinged door with all hardware, without the actual slab cost (that’s quoted per model).
Every quote is a written, itemized price before work starts. Parts, labor, and disposal are locked. The 365-Day Done Right Promise covers parts and labor on the installation for a full year, in writing, no fine-print gymnastics.
DIY or Call Us?
Here’s the honest split. You can safely clean the bottom track on a PGT slider, tighten the handle set screws with a 2.5mm hex key, or wipe down the weatherstripping with silicone lubricant twice a year. That’s maintenance, not repair. Where DIY goes wrong: PGT multi-point lock gearboxes are under spring tension, so opening the lock body without a gear-block tool sends parts across the room, if not into your hand. Hinged PGT doors are heavy, and a slab that comes off its hinges without a second person will crack tile, break a toe, or fold someone’s wrist. And the rollers on sliders require removing the panel, which in a Fort Worth house often means two grown adults and a pry bar. If the hinge sag is bad enough that the door catches on the jamb, call us at (682) 354-9300. We’ll come look, show you the exact part, and hand you a written number before anything comes off the frame. Sean Mackey keeps it simple on every call: get the numbers right up front, and the install takes care of itself.
FAQs
PGT door rollers and hinges in Fort Worth typically last 5 to 8 years before wear becomes noticeable, and the lifespan shortens on doors that face west or get hit with direct afternoon sun. Dust, hard water from irrigation overspray, and the temperature swings between an air-conditioned interior and a 100-degree exterior accelerate wear on the moving parts. If your door is older than six years and starting to drag, you’re on schedule, not unlucky. Call (682) 354-9300 and we’ll tell you whether it’s a clean swap or a frame adjustment.
Yes, in some cases a PGT multi-point lock gearbox can be re-lubricated and the striker plates realigned to buy another year or two, but if the gear teeth are stripped, no repair holds. Rollers can be cleaned and packed with grease once, but once the wheel itself is oval, replacement is the only fix. We’ll show you the worn part and the quote either way, so you never pay for a replacement when a repair does the job. Call (682) 354-9300 for a straight answer.
Most single-part PGT door installations in Fort Worth take 45 minutes to 2 hours on site, including realigning the door and testing the lock and seal. Full slab replacements run a half day. We give you a live arrival time and before-and-after photos of the work, same as every Juniper job.
Yes, our Fort Worth trucks carry PGT-compatible hinge sets, tandem rollers, multi-point lock components, weatherstripping profiles, and threshold caps for the most common residential PGT models. If you need a less common part, we order it from our PGT supplier network and coordinate a return visit at no extra trip charge. Juniper Windows Fort Worth is an independent service provider and not affiliated with PGT Innovations, so we source parts across PGT, CGI, CWS, and ES Windows to match what your home actually needs. Call (682) 354-9300 to schedule your free estimate.
Written by Sean Mackey, Owner, Juniper Windows Fort Worth at Juniper Windows Fort Worth, serving Fort Worth and nearby areas.
Six Reasons Homeowners Choose Juniper Windows Fort Worth
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.