New windows and doors improve comfort, cut energy bills and add long-term value to your home. Juniper Windows Fort Worth pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
Mr-Glass Sliding & Patio Doors: The Fort Worth Owner’s Guide
Mr-Glass sliding and patio doors in Fort Worth can almost always be repaired or replaced without tearing out the frame. We’ve been matching Mr-Glass rollers, handles, locks, and panels for years now – most parts run $85 to $340 installed, and we typically carry the common failure points on the truck. The way most Fort Worth homeowners find us: a door that used to glide with two fingers now takes a shoulder, or a latch that no longer catches, or glass that’s fogged between the panes after a few Texas summers. Here’s exactly what you’re dealing with and what it costs to fix it right.
Which Mr-Glass Models This Applies To
Mr-Glass built sliding patio doors in a few series over the years, and the compatibility gotcha is real: the roller assemblies from a 6000-series door won’t seat properly in a 2000-series track, even when the wheel diameter looks identical. You’ll find the model stamp on the top edge of the sliding panel or on a sticker inside the frame channel – look for a two-letter prefix followed by numbers. If that sticker’s long gone (sunlight eats them in about five years on a west-facing Fort Worth wall), measure the roller housing width and the wheel diameter with a caliper and we can match it. OEM Mr-Glass parts are still available for most series, and quality aftermarket equivalents exist for rollers and latch hardware – we’ll show you both options and let you decide. We also stock compatible hardware for PGT, CGI, and CWS doors if you’re ever in that situation.
Signs Your Mr-Glass Sliding & Patio Doors Are Failing
- The door drags or catches mid-track. Roller wheels flatten on the bottom over time, especially on heavier panels. Fort Worth’s fine clay dust works into the bearings and grinds them down faster than most homeowners expect.
- The handle wiggles but the latch won’t engage. The internal lock rod or the spring-loaded pawl is broken. It’s usually a small zinc part that costs less than $30, but it ruins the door’s security until it’s replaced.
- Condensation between the glass panes. The seal has failed. That fog isn’t cleanable – the insulated glass unit needs replacement, and on Mr-Glass doors that’s a common call for us in older Tarrant County homes.
- The door jumps out of the track or sits visibly crooked. This is almost always a collapsed roller housing, not a track issue. Continuing to force it open risks bending the track itself, which triples the repair cost.
- You feel a draft or see daylight at the corners. Weatherstripping on sliding patio doors in Fort Worth bakes and shrinks in 100-degree summers. It’s an inexpensive fix but ignored too long it lets moisture into the frame channel and rusts the rollers from the inside.
Replacement Cost & What’s Included
For Fort Worth homes, here’s the honest price range we quote on Mr-Glass sliding and patio door parts, installed:
- Roller assembly replacement: $95 – $185 per door (both panels, parts and labor)
- Handle and latch replacement: $75 – $160 (depends on hardware type and finish)
- Weatherstripping replacement: $65 – $110 (full perimeter, all four sides)
- Insulated glass unit replacement: $280 – $640 (depends on glass size, tint, and Low-E coating)
- Track straightening or repair: $120 – $260 (we bend it back true before the new rollers go in)
Every repair gets a written price before we touch the door. No surprise line items. Parts and labor are covered under our 365-Day Done Right Promise – if something fails inside a year, we come back and make it right, no charge. As Sean Mackey puts it: get the numbers right up front, and the install takes care of itself.
DIY or Call Us?
A few things you can safely check yourself: clean the track with a dry brush and a vacuum, tighten the handle screws with a Phillips driver, and wipe down weatherstripping with a silicone lubricant to keep it from cracking. That’s homeowner maintenance, and it genuinely extends door life. But the high-tension parts – roller housings under panel weight, spring-loaded lock mechanisms with stored energy – those are where DIY goes sideways fast. A sliding panel off its track can weigh 150 to 300 pounds. If it comes down on a hand or a foot, you’re looking at a hospital visit, not a weekend fix. Our advice from two decades of this work in Fort Worth: if the door doesn’t glide after a clean track and tightened screws, call us at (682) 354-9300. A roller replacement takes about an hour, and it’s done right the first time.
FAQs
A properly maintained Mr-Glass door should give you 20 to 25 years in Fort Worth, but the wearable parts – rollers, weatherstripping, and latch hardware – typically need attention every 5 to 8 years. That’s normal for any sliding door in this climate, not a defect with the brand. Call us at (682) 354-9300 and we’ll tell you if you need a $100 roller swap or a full panel replacement.
Yes, in most cases. We replace the failed part – the roller, the handle, the glass unit, the weatherstripping – rather than the entire door, unless the frame itself is warped or water-damaged beyond saving. A frame inspection is part of every service call, and we’ll tell you straight if a repair is throwing money at a door that needs replacing.
A roller swap takes about an hour. A handle and latch replacement is 30 to 45 minutes. A full insulated glass unit replacement runs 2 to 3 hours, mostly due to careful glazing and seal work. Weatherstripping is under an hour. We show up with the common parts on the truck, so there’s rarely a second visit needed. Call (682) 354-9300 for a time that works.
We stock the high-failure Mr-Glass parts on the truck – roller assemblies, latch hardware, and weatherstripping for the most common series – so most repairs happen in a single visit. If you have a less common model or an insulated glass unit, we order it and have it in hand before we schedule the install. Juniper Windows Fort Worth is an independent service provider and not affiliated with Mr-Glass, so we’re free to match the right part to your door, OEM or quality aftermarket, without brand bias.
Call Juniper Windows Fort Worth for Your Mr-Glass Parts
If your Mr-Glass sliding or patio door is fighting you, give us a call at (682) 354-9300. We’ll get the details over the phone, give you a realistic price range, and put a written quote in your hand before any work begins. Every repair is covered by our 365-Day Done Right Promise, in writing. And since our Fort Worth location answers calls live around the clock, you’ll never sit on hold wondering if anyone’s coming. Book in a tap, track our arrival, get before-and-after photos, and pay from a link. That’s the Relay Standard, and it’s how every Mr-Glass door repair goes.
Written by Sean Mackey, Owner, Juniper Windows Fort Worth, serving Fort Worth and nearby areas.
Six Reasons Homeowners Choose Juniper Windows Fort Worth
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.