CGI Impact Garage Doors Nationwide

CGI Impact Garage Doors: The Fort Worth Owner’s Guide

CGI impact garage doors in Fort Worth typically run $2,400 to $6,800 installed, depending on size, window configuration, and which CGI line your home carries. We stock CGI impact doors and the parts that keep them working, and we’re usually out the same week you call. Most Fort Worth owners find this page because their door took a hit during spring storm season, or because an opener is fighting a door that suddenly weighs more than it should.

Call (682) 354-9300

Here’s the picture we see constantly in Tarrant County: a CGI door that’s been doing its job for eight or ten years, then one afternoon a spring lets go, or a bottom seal fails, or the track flexes just enough that the rails start grinding. The door itself is often still fine. The parts around it are not.

Which CGI Models This Applies To

CGI builds impact-rated garage doors across a few distinct lines, and the parts don’t always swap between them. The two most common in Fort Worth are the CGI sentinel line (single and double-car, no windows or optional cyclone-rated glass) and the CGI estate line (heavier gauge, township-approved for coastal and high-wind zones). Within each line, CGI uses model-specific spring kits, hinge assemblies, and roller tracks. If your door is pre-2018, you may also have a first-generation bottom retainer that CGI updated because it pinched the weatherseal in extreme heat. That matters here, because Fort Worth summers bake a garage door the way coastal salt spray never will.

How to identify what you have: look for a white product label on the left door panel near the hinges, about knee height. It lists the line name, the door width and height (like 168 x 84), and the spring ID. If the label is worn off, we can match the door by measuring the panel profile and counting the spring coils. On the parts question: CGI’s OEM springs and hinges are well made and what we install by default. For tracks and rollers, we’ll often recommend a quality aftermarket equivalent that carries a longer wear rating in Texas heat. We’ll show you both options and price the job honestly before anything gets ordered.

One compatibility gotcha to know: CGI single-car doors run a narrower track profile than their double-car doors, and ordering the wrong track set is the most common ordering mistake we see from homeowners going it alone. The second is window kits. CGI impact glass is not a universal cut; it’s glass made for a specific panel stamping. Get the panel number wrong and you’ll wait two weeks for the wrong piece.

Signs Your CGI Impact Garage Doors Is Failing

• The door opens a few inches, then stops or reverses. This is almost always a spring losing tension or an opener’s force sensor reading too much resistance. A door that’s lost spring support is one of the most dangerous situations in a garage.
• You hear a loud bang from the garage, like a rifle shot. That’s a torsion spring snapping. It happens most often on cold mornings, but in Fort Worth we hear it year-round when cycles add up. Do not open the door manually after this. Call us.
• The door sags on one side or scrapes the frame on the way up. A stretched cable or a worn hinge. If you let it keep cycling, it’ll carve grooves into the track and turn a $195 repair into a full track replacement.
• Water pools at the base of the door after rain. The bottom seal has compressed or torn. On an impact door, this isn’t cosmetic; the seal is part of the wind-resistance envelope. A gap also lets Fort Worth’s mosquitos and scorpions walk right in.
• The door shakes or wobbles mid-cycle. Roller bearings are done. Most CGI doors ship with standard rollers rated for roughly 10,000 cycles. In a home where the garage door opens four times a day, that’s about seven years. The door’s in fine shape. The rollers aren’t.

Replacement Cost & What’s Included

For a full CGI impact door replacement in Fort Worth, plan on $2,400 to $6,800 installed. A single-car door without windows starts at the low end; a double-car in the estate line with impact-rated glass and a higher wind-load rating lands at the top. Spring replacement alone runs $180 to $320. Hinges and roller kits run $165 to $290. Track replacement runs $380 to $620, and a bottom seal runs $90 to $140. These are Fort Worth market prices, parts and labor together, not a national average you have to squint at.

What drives the price: door size (obviously), whether your CGI line needs OEM-only glass, how much hardware we have to replace around the door panel, and whether the opener needs a force re-set once the new parts are in. Some Fort Worth homes with older garage framing also need shimming or track re-mounting. We give a written line-item price before any work starts, and that price doesn’t move. The work is covered by our 365-Day Done Right Promise: if something’s wrong within a year, it’s on us, parts and labor, in writing.

DIY or Call Us?

There’s one thing on any garage door you should not touch, and that’s the spring. Torsion springs hold enough tension to break bone or take a finger off if a winding bar slips. Cables are the same story. If your CGI door has a snapped spring or a frayed cable, leave the door closed and call (682) 354-9300.

What you can do safely: check that both photo-eye sensors are clean and aligned, replace the batteries in your opener keypad, clear debris from the track with the door closed, and take a close look at whether the bottom seal is visibly cracked. Those checks cost you ten minutes and help us diagnose the problem before the truck rolls. If it turns out to be a seal or rollers, you’ll know from the price list above roughly where the job lands. The spring and cable stuff: that’s ours.

FAQs